DC Pulse Signal Low Power Solenoid Valve
We Mainly do Pneumatic Cylinder, solenoid valve, pneumatic valve, air treatment units, quick connection fittings and PU tube . Our 4V. 3V.2V.2p .solenoid valve ,and 4A.3A Pneumatic valve sell so hot in Asia, Europe,and Middle East. We are popular in pneumatic and Hydraulic market. Our accessories taked from the same supplier as Airtac.
DC Pulse Signal Low Power Solenoid Valve
Basic Info:
We Mainly do Pneumatic Cylinder, solenoid valve, pneumatic valve, air treatment units, quick connection fittings and PU tube .
Our 4V. 3V.2V.2p .solenoid valve ,and 4A.3A Pneumatic valve sell so hot in Asia, Europe,and Middle East.
We are popular in pneumatic and Hydraulic market. Our accessories taked from the same supplier as Airtac.
Product Overview
DC Pulse Signal Low Power Solenoid Valve is driven by DC pulse signal, only needs instantaneous power to complete opening and closing, no long-term power-on work.
It features low energy consumption, stable performance and long service life, widely used in water meter control, intelligent fluid equipment, remote automatic control and other scenes requiring low power operation.
General Specifications
| Parameter | Specification | Remarks / Selection Notes |
|---|---|---|
| Product Series | DC Pulse Type Low Power Solenoid Valve | Permanent magnet self-holding type |
| Operating Principle | Pulse signal drive + permanent magnet self-holding | State self-locks after instantaneous energization |
| Pulse Width | 20 ~ 50 ms (milliseconds) | Depends on specific model |
| Operating Voltage | DC3V, DC6V, DC9V, DC12V, DC24V | Multiple voltage options |
| Coil Resistance | Approx. 16Ω ~ 50Ω (voltage dependent) | |
| Opening Pulse Current | Approx. 250mA ~ 500mA | Instantaneous current |
| Holding Power Consumption | 0 W (permanent magnet self-holding) | Zero standby power |
| Body Material | Brass / Stainless Steel SUS304 | Optional |
| Sealing Material | EPDM / NBR | Water and temperature resistant |
| Suitable Media | Water, air, light liquids | Irrigation, faucet applications |
| Working Pressure | 0.02 ~ 0.8 MPa (0.2-8 bar) | |
| Media Temperature | 0°C ~ 60°C | Normal temperature media |
| Port Size | DN15 (1/2"), DN20, DN25 | Customizable on request |
| Connection Type | Female thread (G1/2" / G3/4" / G1") | Standard pipe thread |
| Design Life | ≥ 1.2 million cycles | |
| Response Time (Open) | ≤ 0.15 seconds | |
| Response Time (Close) | ≤ 0.5 seconds | |
| Protection Rating | IP65 (standard) / IP67 (short-term immersion) | Waterproof cable lead wire |
| Explosion-Proof Rating | Explosion-proof type optional | Suitable for gas and hazardous locations |
| Manual Override | Standard on some models | Emergency operation function |
| Built-in Filter | Optional | Enhances anti-contamination capability |
Dimensions & Specifications by Size
| Connection (G/NPT) | DN | Valve Dimensions (L×W×H mm) | Cv Value | Max Pressure |
|---|---|---|---|---|
| 1/2" | 15 | 68 × 48 × 125 | 4.5 | 0.03~7.5MPa |
| 3/4" | 15 | 68 × 48 × 125 | 4.5 | 0.03~7.5MPa |
| 1" | 25 | 96 × 70 × 145 | 12 | 0.03~7.5MPa |
| 1¼" | 32 | 150 × 135 × 170 | 25 | 0.03~7.5MPa |
| 1½" | 40 | 160 × 145 × 180 | 31 | 0.03~7.5MPa |
| 2" | 50 | 185 × 155 × 210 | 50 | 0.03~7.5MPa |
Temperature Ratings by Seal Material
| Sealing Material | Temperature Range | Suitable Media |
|---|---|---|
| NBR | -20℃ ~ +80℃ | Air, water, natural gas |
| EPDM | -40℃ ~ +120℃ | Hot water |
| VITON / PTFE | -50℃ ~ +260℃ | Oil, hot water, low-pressure steam |
Sealing Materials & Temperature Range
| Seal Code | Sealing Material | Fluid Temperature | Suitable Media |
|---|---|---|---|
| X=N | NBR | -20℃ ~ 80℃ | Air, water, natural gas |
| X=E | EPDM | -20℃ ~ 135℃ | Hot water |
| X=V | VITON | -10℃ ~ 155℃ | Hot oil, hot water |
Model & Specification Table (G/NPT Thread Connections)
| Port Size | Orifice (mm) | Flow (Cv) | Pressure Rating |
|---|---|---|---|
| 1/2" | 15 | 4.5 | 0.3~16 Bar |
| 3/4" | 20 | 7.6 | 0.3~16 Bar |
| 1" | 25 | 12 | 0.3~16 Bar |
| 1½" | 40 | 19.2 | 0.3~16 Bar |
| 2" | 50 | 24 | 0.3~16 Bar |
Electrical Specifications
| Voltage | Coil Power | Operating Current | Coil Model | Connection Type |
|---|---|---|---|---|
| AC220V | 9VA | 0.04A | BA11 | Junction box |
| DC24V | 8W | 0.35A | BA11 | Junction box |
| AC110V | 9VA | 0.82A | BA11 | Junction box |
| DC12V | 8W | 1.68A | BA11 | Junction box |
| AC24V | 9VA | 0.375A | BA12 | 300mm lead wires |
| AC36V | 9VA | 0.25A | BA12 | 300mm lead wires |
Quick Selection Guide
| Nominal Diameter | Pipe Size | Recommended Model |
|---|---|---|
| DN10 | 3/8" | 2W-15-31X |
| DN15 | 1/2" | 2W-15-41X |
| DN20 | 3/4" | 2W-20-51X |
| DN25 | 1" | 2W-25-61X |
| DN32 | 1-1/4" | 2W-32-71X |
| DN40 | 1-1/2" | 2W-40-81X |
| DN50 | 2" | 2W-50-91X |
Media & Seal Material Selection
|
Selection Tips
1, Voltage Matching: AC220V is for standard mains power; DC24V/12V are better for industrial control, vehicle, and low-voltage systems. Always confirm the coil voltage to avoid burnout. 2,Temperature Limits: The seal material determines the maximum operating temperature. For example, NBR (80°C max) is not suitable for continuous use in hot water above 80°C, as it will degrade and leak. 3,Media Compatibility: Oily media requires VITON seals, as NBR will swell and fail in oil. Steam applications should use VITON or higher-grade seals. 4,Size Consistency: Always match the valve size to your pipe's nominal diameter. Using a smaller valve will restrict flow and shorten its lifespan.
Supplementary Key Points (3 Points Summary)
✅PTFE Seal UpgradePTFE sealing is newly upgraded, with temperature resistance up to 260℃, excellent resistance to strong acid, alkali and organic solvents, ideal for chemical and high-temperature steam working conditions.
✅Dual Power OptionsIt provides dual power specifications: 22VA/30VA for AC and 17W/24W for DC, matching different coil types and adaptable to customers' various power load requirements.
✅Model Code RuleThe letter X in the model stands for sealing material code: N=NBR, E=EPDM, V=VITON; just replace it directly when ordering.
Our Advantages:
✅Adopts DC pulse drive, ultra-low power consumption, energy-saving
✅Pulse instant action, fast response, stable switch operation
✅Keep state without continuous power supply, longer service life
✅Fine sealing structure, no leakage, safe and reliable
✅Small volume compact design, easy to install and arrange
✅Wide voltage adaptability, strong anti-interference ability |
|
|||||||||||||||||
Production Workshop：
Where to be used：
Supplier's popular products:
![KJW1D7LNZMZJLDZ(NEL[]RB](/Content/uploads/2020480534/20200610134717b0421f6654e94d0da8c0a2ff0841247c.png "product-803-416")
Tips:
1. Your inquiry related to our products or prices will be replied in 24 hours
2. Well-trained and experienced staffs to answer all your inquiries in fluent English.
3. OEM&ODM, any your customized lightings we can help your to design and put into product.
4. Distributorship is offered for your unique design and some our current models.
5. Protect your sales area, ideas of design and all your private information.
When selecting a stainless steel pneumatic air gripper cylinder, consider factors such as gripping force, stroke length, operating pressure, compatibility with the object size and weight, and the specific environmental conditions of your application. It is advisable to consult the manufacturer's specifications and guidelines to ensure the proper selection, installation, and operation of the gripper cylinder for your specific requirements.
Hot Tags: dc pulse signal low power solenoid valve, China, manufacturers, suppliers, factory, customized, low price, made in China
Send Inquiry
